ORIENTAL Electric Motor - US2 series

Electric Motor - US2 series

ดาวน์โหลดไฟล์ PDF

Feature | Electric Motor - US2 series

เมื่อต่อใช้งานร่วมกับหัวเกียร์ ส่งผลให้มีความเร็วช้าลงเท่ากับความต้องการหรือมีแรงเพิ่มมากขึ้น ผลิตภัณณฑ์ที่ใช้ได้ World K series ใช้แรงดันไฟฟ้าของแหล่งจ่ายไฟในเอเชีย 6W ถึง 40W มอเตอร์ที่มีเฟืองแบบ GN 60W, 90W มอเตอร์ที่มีเฟืองแบบ GE

---

Specifications | Electric Motor - US2 series

Electric Motor - US2 series
Combination Motor	แรงดันไฟฟ้าของแหล่งจ่ายไฟ [VAC]	แถวบน: ขนาดหน้าแปลน [mm]/แถวล่าง: ขนาดกำลัง [W]
		60	70	80	90	90	90
		6	15	25	40	60	90
Parallel Shaft	Single-Phase 110/115	•	•	•	•	•	•
	Single-Phase 220/230	•	•	•	•	•	•
Round Shaft	Single-Phase 110/115	•	•	•	•	•	•
	Single-Phase 220/230	•	•	•	•	•	•

---

Electric Motor		US2 series
		Motor	Speed Controller
Insulation Resistance		The measured value is 100 MΩ or more when 500 VDC megger is applied between the motor winding and the case after continuous operation under normal ambient temperature and humidity.	The measured value is 100 MΩ or more when a 500 VDC megger is applied between the main circuit terminal and the input signal terminal, between the main circuit terminal and the case, and between the main circuit terminal and FG, after continuous operation under normal ambient temperature and humidity.
Dielectric Stregth Voltage		No abnormality is judged even with application of 1.5 kVAC at 50/60 Hz between the windings and the case for 1 minute afer continuous operation under normal ambient temperature and humidity.	No abnormality is judged even with application of 1.9 kVAC at 50/60 Hz between the main circuit terminal and the input signal terminal and between the main circuit terminal and the case, and 1.5kVAC at 50/60 Hz between the main circuit terminal and FG for 1 minute adter continuous operation under normal ambient temperature and humidity.
Temperature Rise		A gearhead or equivalent heat sink*1 is connected to the motor and the winding temperature rise is measured at 80°C or less using the resistance change method after continuous operation with no load under normal ambient temperature and humidity.	-
Overheat Protection Device		The 6 W type inpedance protected. All ofther motors have a built-in thermal protector (Automatic return type). Open: 130±5°C, Close: 80±20°C	-
Operating Environment	Ambient Temperature	-10 ถึง 40 °C (Non-freezing)	0 to 50°C (Non-freezing)
	Ambient Humidity	85% or less (Non-freezing)
	Altitude	Up to 1000m above sea level
	Atmosphere	No corrosive gases or dust. Not exposed to water or oil. Cannot be used in a radioactive area, magnatic field, vacuum, or other special environments.
	Vibration	Not subject to continuous vibration or excessive shock Conforms to JIS C 60068-2-6 "Sine-wave vibration test method" Frequency range: 10-55Hz, Pulsating amplitude: 0.15m Sweep direction: 3 direction (X, Y, Z) Number of sweeps: 20 times
Storage Condition*2	Ambient Temperature	-25 to 70 °C (Non-freezing)
	Ambient Humidity	85% or less (Non-freezing)
	Altitud	Up to 3000m above sea level
	Atmosphere	No corrosive gases or dust. Not exposed to water or oil. Connot be used in a radioactive area, magnetic field vacuum, or other special environments.
Heat-resistant Class		130 (B)	-
Degree of Protection		IP20	IP20

*1 Heat sink size (Materual:Aluminum)
*2 The storage condition applies to a short period such as a period during transportation.